March 29, 2002
Berkeley Lab Research News
NEW HYBRID SOLAR CELLS COMBINE NANOTECH WITH PLASTICS
Lab news releases

Sign up to receive our news releases via email

Science Beat: most recent science news here

Berkeley Lab home page

Lab A to Z website index

Search news articles archive
 
 Advanced Search  
Search Tips

BERKELEY, CA   A new generation of solar cells that combines nanotechnology with plastic electronics has been launched with the development of a semiconductor-polymer photovoltaic device by researchers with the U.S. Department of Energy's Lawrence Berkeley National Laboratory (Berkeley Lab) and the University of California at Berkeley (UCB). Such hybrid solar cells will be cheaper and easier to make than their semiconductor counterparts, and could be made in the same nearly infinite variety of shapes as pure polymers.

Alivasatos group
Janke Dittmer, Wendy Huynh, and team leader Paul Alivisatos created tiny solar cell assemblies (shown held by a tweezer, upper right) using nanoscale semiconducting rods of polymer and cadmium selenide

Paul Alivisatos, a chemist who holds a joint appointment with Berkeley Lab's Materials Science Division (MSD) and UCB's Chemistry Department, led the research team, who reported their hybrid solar cell development in the March 29, 2002 issue of the journal Science. Other members of the team were Wendy Huynh, a graduate student with UCB's Chemistry Department, and Janke Dittmer, an MSD staff scientist.

"We have demonstrated that semiconductor nanorods can be used to fabricate readily processed and energy-efficient hybrid solar cells together with polymers," says Alivisatos, a leading authority on the production of nanosized semiconductor crystals and director of the Molecular Foundry, a center for nanoscience now being established at Berkeley Lab.

The use of solar, or photovoltaic, cells — devices that can absorb and convert light into electrical power — has been limited to date because production costs are so high. Even the fabrication of the simplest semiconductor cell is a complex process that has to take place under exactly controlled conditions, such as high vacuum and temperatures between 400 and 1,400 degrees Celsius.

Ever since the discovery in 1977 of conducting plastics (polymers which feature conjugated double chemical bonds, that enable electrons to move through them), there has been interest in using these materials in the fabrication of solar cells. Plastic solar cells can be made in bulk quantities for a few cents each; however, the efficiency with which they convert light into electricity has been quite poor compared to the power-conversion efficiencies of semiconductor cells.

"The advantage of hybrid materials consisting of inorganic semiconductors and organic polymers is that potentially you get the best of both worlds," says Dittmer. "Inorganic semiconductors offer excellent, well established electronic properties, and they are very well suited as solar cell materials. Polymers offer the advantage of solution processing at room temperature, which is cheaper and allows for using fully flexible substrates, such as plastics."

At the heart of all photovoltaic devices are two separate layers of materials, one with an abundance of electrons that functions as a "negative pole," and one with an abundance of electron holes (vacant, positively-charged energy spaces) that functions as a "positive pole." When photons from the sun or some other light source are absorbed, their energy is transferred to the extra electrons in the negative pole, causing them to flow to the positive pole and creating new holes that start flowing to the negative pole. This electrical current can then be used to power other devices such as a pocket calculator.

In a typical semiconductor solar cell, the two poles are made from n-type and p-type semiconductors. In a plastic solar cell, they're made from hole-acceptor and electron-acceptor polymers. In their new hybrid solar cell, Alivisatos, Huynh, and Dittmer used the semicrystalline polymer known as poly(3-hexylthiophene), or P3HT, for the hole acceptor or negative pole, and nanometer-sized cadmium selenide (CdSe) rods as the positive pole.

"We chose P3HT because it can be processed in solution and has been used by many research groups around the world who are working on plastic transistors," says Huynh. "Also, it is the conjugated polymer with the highest hole mobility found so far. Higher hole (and electron) mobility means that charges are transported more quickly, which reduces current losses."

The cadmium selenide rods measured 7 nanometers in diameter and 60 nanometers in length (a nanometer is one billionth of a meter, less than one-hundred millionth of an inch). Alivisatos led an earlier study in which the technique for growing semiconductor nanocrystals into two-dimensional rods was first developed. Prior to that work, nanocrystals had always been grown as one-dimensional spheres. Using rod-shaped nanocrystals rather than spheres provided a directed path for electron transport to help improve solar cell performance.

"With CdSe rods measuring 7 nanometers by 60 nanometers, our hybrid solar cells achieved a monochromatic power conversion efficiency of 6.9 percent, one of the highest ever reported for a plastic photovoltaic device," says Alivisatos. Monochromatic power efficiency measures the ability to convert room light (which is mostly visible light) into electricity.

The Berkeley researchers prepared their solar cells by codissolving the nanorods with the P3HT and spin-casting the hybrid solution onto a glass substrate. They found that by keeping the length of the rods constant while modifying the diameter enabled them to tune the absorption spectrum of the cells so that it overlapped with the solar emission spectrum. This not only enables their hybrid cells to collect more light than typical plastic solar cells, but it also opens the door for high-efficiency devices in the future, such as tandem solar cells.

Although the efficiency of the Berkeley hybrid cells for converting sunlight into electricity was only 1.7 percent at A.M. 1.5 (when the sun is at a 41.8-degree angle to the horizon), which is far off the mark of the best semiconductor solar cells, Dittmer says there is ample opportunity for improvement.

"The most important step is to increase the amount of sunlight absorbed in the red part of the spectrum, which we can do by going to other semiconductor materials such as cadmium telluride. Also, our published hybrid solar cells have a very simple structure, in order to investigate the science behind them. In the future, many engineering tricks can be applied to make the cells more efficient." The Berkeley researchers have already been approached by companies that are interested in commercializing this technology.

Berkeley Lab is a U.S. Department of Energy national laboratory located in Berkeley, California. It conducts unclassified scientific research and is managed by the University of California.